Contact TechDocs
If you are not finding the results you need and still have questions, submit a request using the form below and our Tech Docs team will get right on it. Our goal is to provide the content you need!
L Class Q&A
- FAQ | Why do the LA108/LA112 feature only three adjustable vertical splay angles?
- FAQ | The LA108 has less specified amplifier Watts than a KLA12. Does that mean that the LA108 is not as loud as a KLA12?
- FAQ | How many LA108/LA112 loudspeakers can be flown in an array?
- FAQ | How many LA108/LA112 loudspeakers can I deploy on a loudspeaker stand?
- FAQ | How many LA108/LA112 loudspeakers can I deploy on a pole over a subwoofer?
- FAQ | What are the angles of the dual loudspeaker pole cup available on the bottom of the LA108/LA112?
- FAQ | What is the coverage pattern of the LA108 and LA112?
- FAQ | Can the rigging hardware of the LA108 connect to the LA112?
- FAQ | What is Ar-Q™ Array Equalization?
- FAQ | After setting up my loudspeaker array, how do I apply the correct Ar-Q™ Array Equalization settings for my deployment?
- FAQ | What is the purpose of the infrared (IR) transmitter/receiver on the top/bottom of each LA108/LA112 loudspeaker’s grille?
- FAQ | What are the Dante®/Network EtherCON ports for on the LA108/LA112?
- FAQ | Is the second EtherCON port on LA108/LA112 for network redundancy (primary vs secondary)?
- FAQ | If there is no Dante® network redundancy on the LA108/LA112, what other fail over is supported?
- FAQ | The KLA12 loudspeaker had an 18° vertical coverage angle, while the LA108/LA112 feature a 15° vertical coverage angle. Does that mean the KLA12 covers more audience area than the LA108/LA112?
- FAQ | Can I use KLA12 and LA112 loudspeakers together in the same array?
- FAQ | Does QSC offer any recommendations regarding a ratio of LS118 subwoofers to LA108/LA112 loudspeakers?
- FAQ | Can I connect to my L Class loudspeaker array with Dante® and then pass the signal through the rest of the array with analog XLR cables?
- FAQ | Can I connect to my L Class loudspeaker array with an analog cable and then pass the signal through the rest of the array using RJ45 network cables?
- FAQ | Can I use the LA108/LA112 in vertical orientation (enclosure placed on its side) for stage side-fills, for example?
- FAQ | Can I use L Class models in applications where they may be exposed to rain or other sources of moisture?
- FAQ | What is the operating ambient temperature range at which LA108/LA112 will perform according to their specifications?
- FAQ | What is QSC Acoustic Linear Phase (ALP) design?
- FAQ | Which QSC loudspeakers feature Acoustic Linear Phase (ALP) design?
- FAQ | How many L Class models can I connect via switch hops on a single network run from my router or switch?
- FAQ | How is Dante® audio distributed to an L Class array?
- FAQ | Can you enlist remote monitoring and management for fixed installations if you integrate L Class line array with the Q-SYS Platform and Q-SYS Reflect?
- FAQ | Can the LS118 run in cardioid mode?
- FAQ | Is the LS118 flyable?
- FAQ | Can I fly an array of LA108/LA112 underneath the LS118?
- FAQ | Is the performance of the LS118 altered/modified when used on its side?
- FAQ | What is linear phase and why should anyone care about it?
Popular Articles
- Error | Protect Mode 4 on K.2 Series loudspeakers
- Troubleshooting | K.2 Speaker Displaying Firmware 9.1.1.x
- How To | Removal and Installation of K.2 Amp Module for Service
- Troubleshooting | TouchMix DAW Utility not installing/opening in MacOS
- How To | Setup the TouchMix TM-30 DAW Connection for MAC.
- Troubleshooting | K.2 Loudspeaker Does Not Pass Audio
- How To | K.2 Firmware Installation > macOS
- FAQ | Do the RMXa Series amplifiers have Universal Power Supplies?
- Troubleshooting | K.2 Loudspeaker Does Not Turn On